液壓安全閥

◎液壓安全閥（GYA型）GYATypedeadweightsafetyvalve一、產品概述ProductOverview液壓安全閥是安裝呼吸閥儲罐上配置的安全閥門，當呼吸閥出現故障或不能有效啟動，儲罐內外壓力失去平衡超過規定值，液壓安全閥將自動啟動工作，保護儲罐不被破壞

◎ 液壓安全閥（GYA型）

GYA Type dead weight safety valve

一、產品概述Product Overview

液壓安全閥是安裝呼吸閥儲罐上配置的安全閥門，當呼吸閥出現故障或不能有效啟動，儲罐內外壓力失去平衡超過規定值，液壓安全閥將自動啟動工作，保護儲罐不被破壞；與呼吸閥配套使用，有著雙保險保護儲罐作用；液壓安全閥應與同規格阻火器配套，特別適應北方寒冷氣候地區使用，廣泛應用于油田、石化廠、油庫等儲存原油、汽油、煤油、柴油、芳烴等液體介質的儲罐。

Hydraulic valve is installed the configured safety valve in the breathing valve on the tank breathing valve fails or can not effectively start, the pressure inside and outside the tank out of balance exceeds the specified value, the hydraulic valve will automatically start working to protect the tank is not destroyed;supporting the use of the breathing valve has a double insurance protection tank role; hydraulic valve with the same specifications flame arrester supporting, in particular, to adapt to the cold weather in northern regions, widely used in oil, petrochemical plants, oil depots and storage of crude oil, gasoline, kerosene,diesel oil, aromatic hydrocarbons such as liquid medium tank.

二、主要用途Main Use

1、液壓安全閥是（活瓣式）呼吸閥的安全備用設備，它的吸氣和呼氣的動作壓力略高于（活瓣式）呼吸閥，在呼吸閥一旦失靈或在冬季其活瓣凍結時，液壓安全閥的液封即被破壞從而保護油罐免遭破壞。

2、液壓安全閥裝于油罐頂部與呼吸閥配合使用。

3、控制壓力：+200毫米水柱至~-45毫米水柱。

1.hydraulic valve (valve type) breathing valve a safety backup device, the action of the inspiratory and expiratory pressure slightly higher than the (valve) breathing valve in the breathing valve failure or valve in the winterfreeze, hydraulic valve liquid seal incurs damage so as to protect the tank from destruction.

2.hydraulic valve mounted at the top of the tank with the breathing valve used in conjunction.

3.the control pressure: +200mmH2O ~ -45mm mmH2O.

三、安裝事項Installation Item

1、液壓安全閥應示意圖進行安裝，保證安全閥對接合管法蘭垂直，垂直度允差應小于50。

2、安裝液壓安全閥之前，先對液壓安全閥進行檢查，用溶劑洗擦灰塵和其它粘性物質；

3、液壓安全閥安裝的法蘭標準及壓力如下：PN0.6MPa.JB78-59。

4、液壓安全閥安裝完畢后，摘下閥罩，在集油槽內注入變壓器油，保持液面與溢流管頂平。

1．hydraulic valve schematic diagram for installation, ensure that the safety valve of the joint pipe flange vertical, vertical tolerances should be less than 50.

2．the before installing hydraulic valve, the first hydraulic valve inspection with a sol vent scrubbing dust and other sticky substances;

3．flange standards and pressure of hydraulic valve installed as follows: PN0.6MPa. JB78-59.

4．the hydraulic valve installed, take off the valve cover, the injection transformer oil sump to maintain the top level of the liquid level of the overflow pipe.

四、維護保養Maintenance

1、設備保養人員在儲罐每次收或發作業前應認真檢查液壓安全閥的油位標準，及時補油；

2、一般一年應清洗一次液壓安全閥的集油槽并更換新的液壓油。

3、為確保儲罐的安全，注入的液壓油油位尺顯示不可大于60mm。

4、至少三個月檢查一下阻火器，將阻火器網上的灰塵及鐵銹清除清洗干凈，避免阻火網堵塞，造成液壓安全閥失效，儲罐被抽癟事故發生。

企業業績：

中國神華寧夏煤業集團有限公司83萬噸/年二甲醚項目

、45萬噸/年醋酸乙烯裝置

泉州恒河化工有限公司4萬噸/年碳酸二甲酯項目

海南椰島集團保健酒生產基地（二期）項目

煙臺萬華聚氨酯股份有限公司環氧丙烷及丙烯酸酯一體化項目

中遠關西涂料（上海）有限公司新建7萬噸涂料項目